Actia Psa Xs Evolution 9780z5 Driver Upd Info

: Once installed, plug in your VCI. Open Device Manager . It should appear under "Universal Serial Bus controllers" as "ACTIA USB Devices" or similar. 4. Troubleshooting Common Issues PSA XS Evo driver help | Peugeot Forums

Perfect for native installs of older Lexia 3 and PP2000 code. Partial Driver signatures must be manually allowed during setup. Windows 10 (64-bit) Restricted

Here is a blog post guide designed to help you navigate the driver and firmware updates needed to get your device running smoothly.

The 9780.Z5 is the hardware interface (probe) designed by ACTIA. It connects the vehicle’s OBD2 port to a PC via USB.

The is the small but critical program that allows your Windows operating system to recognize the "Actia PSA XS Evolution 9780Z5" when plugged into a USB port. Without the correct driver, your computer will see an "Unknown USB Device" rather than the diagnostic tool. actia psa xs evolution 9780z5 driver upd

The driver is rarely a standalone download from Actia for end-users. Instead, it is typically bundled with Diagbox software updates. Look in C:\AWROOT\bin\fi\APPDIAG.SYS .

To update, click , select your desired .APPLI firmware file, and click Downloading . Do not unplug the USB cable during this process. Troubleshooting Common Driver Errors Error: "Device Not Recognized" / Code 43

If you run into persistent driver errors, a fresh installation of DiagBox without an internet connection, combined with the "PSA Interface Checker" tool, is almost guaranteed to resolve the issue. The knowledge base surrounding the 9780Z5 is vast, and with the right driver update strategy, your interface will continue to serve you as the definitive tool for French and Stellantis vehicles for years to come.

Actia PSA XS Evolution 9780z5 Driver Update Guide: Fix Connectivity & Boost Diagnostics in 2026 : Once installed, plug in your VCI

Launch DiagBox, go to the Settings menu, and select Interface Calibration/Reflash .

Proper driver installation is critical for the hardware to communicate with your diagnostic software.

: When you launch a recent version of DiagBox (e.g., v7.40+), the software typically checks the connected VCI and automatically pushes the required firmware update (such as or higher) to the device. Manual Driver Installation Disconnect the VCI from your computer. Download the latest Level X driver from the ACTIA Support Portal Run the installer with Administrator rights

This usually means the driver is installed, but the is out of sync with the software version. If you are using Diagbox 9.129 but your interface has firmware 4.2.2, you may need to run the firmware updater included with your driver package to bring it to 4.3.7 or higher. 64-bit vs 32-bit Compatibility Windows 10 (64-bit) Restricted Here is a blog

If your vehicle is pre-2010, the software may prompt you to use PP2000 instead of the newer Lexia interface within DiagBox. 5. Summary Table: Actia XS Evolution 9780.Z5 Setup Recommendation for 2026 Interface Model XS Evolution 9780.Z5 Recommended OS Windows 10 (64-bit preferred) Driver Location Inside DiagBox /drivers folder Common Error "No Interface Detected" / USB Com Board Issue Key Action Update USB Driver via Device Manager

: Poor USB power delivery, a low-quality clone cable, or USB 3.0 controller incompatibility.

Once rebooted, use the Device Manager to manually "Browse my computer for drivers" and select the ACTIA folder. Troubleshooting Common Errors "Init KO" or "Device Not Detected"

This is the practical, hands-on section. Follow these steps precisely.

XS FAMILY. Basic+ XS / CAT Level X driver | Version 2.9.0.8, for Windows 8 (x86/amd64) | Windows 10 (x84/amd64) | Windows 11 (x86/ Genuine Actia XS not found - French Car Forum